control systems, heat recovery

HT SeriesThe Len Gordon Co’s HT Series safety air switch control packages are designed specifically for pump motor heat transfer systems. There are two models to choose from, each with its own deck control. Both models operate in essentially the same manner, providing thermostatic control of the pump motor as well as a 10-minute time delay and air activated hi limit resetThe HT-1000-Y2K/HT-2000-Y2K is a smaller box containing one air switch that controls the pump and an electronic hi limit which is reset by the same button controlling the pump. The Micro-Topside control is substantially smaller and may only be used with the HT-1000-Y2K/HT-2000-Y2K controlsMust order pump cord separately 58-439-2620 AI #3-73-5000

Balboa Heat Jacket System This system is pre wired with a 15A 120v GFCI cord end. It is designed exclusively for Heat Recovery Jacket systems. Featuring separate heat up/down buttons and a standby mode, this system can operate a 1 speed, 120v pump and a 12v light. Automatic filter, freeze, and hi limit circuits are built in. (control panel required and is sold separately 58-138-2600 52973-04

Hydrothermix "Thermal Wrap" Heat Transfer KitThis patented new heat transfer system absorbs the heat energy generated by the pump/motor and redistributes it back into the water. The Hydrothermix system will maintain and increase water temperature, allow the motor to run cooler, and increase its longevity. Hydrothermix is manufactured from a specially engineered polymer compound that insures maximum thermal conductivity and durability. There are no moving parts, no electrical connections, and nothing to wear out. Hydrothermix jacket kits will allow retrofit to almost any spa or bath wet end 46-405-1320 53S

Heat Jacket Parts Kit, Barb Union 47-405-1000

Heat Recovery Control SeriesThis series of controls is designed specifically for spas employing motor heat recovery jackets. The control includes a hi limit with remote, spaside reset, a 10-minute timer circuit for direct pump control, two momentary contact air switches for hi limit reset and timer control initiation, and three power cords for line, pump, and spaside control faceplate label designed of these controls incorporates READY, HEAT ON, and TEMP FAULT indicators which are illuminated to display equipment status. Not regularly stocked but can be special ordered. 58-319-2500 HRC2003-120

Heat Recovery Control SeriesThis series of controls is designed specifically for spas employing motor heat recovery jackets. The control includes a hi limit with remote, spaside reset, a 10-minute timer circuit for direct pump control, two momentary contact air switches for hi limit reset and timer control initiation, and three power cords for line, pump, and spaside control faceplate label designed of these controls incorporates READY, HEAT ON, and TEMP FAULT indicators which are illuminated to display equipment status. Not regularly stocked but can be special ordered. 58-319-2525 HRC2006-120

HT SeriesThe Len Gordon Co’s HT Series safety air switch control packages are designed specifically for pump motor heat transfer systems. There are two models to choose from, each with its own deck control. Both models operate in essentially the same manner, providing thermostatic control of the pump motor as well as a 10-minute time delay and air activated hi limit resetThe HT-1000-Y2K/HT-2000-Y2K is a smaller box containing one air switch that controls the pump and an electronic hi limit which is reset by the same button controlling the pump. The Micro-Topside control is substantially smaller and may only be used with the HT-1000-Y2K/HT-2000-Y2K controlsMust order pump cord separately 58-439-2627 930113-101

Heat Recovery Control SeriesThis series of controls is designed specifically for spas employing motor heat recovery jackets. The control includes a hi limit with remote, spaside reset, a 10-minute timer circuit for direct pump control, two momentary contact air switches for hi limit reset and timer control initiation, and three power cords for line, pump, and spaside control faceplate label designed of these controls incorporates READY, HEAT ON, and TEMP FAULT indicators which are illuminated to display equipment status 58-319-1170 30264BM

HT SeriesThe Len Gordon Co’s HT Series safety air switch control packages are designed specifically for pump motor heat transfer systems. There are two models to choose from, each with its own deck control. Both models operate in essentially the same manner, providing thermostatic control of the pump motor as well as a 10-minute time delay and air activated hi limit resetThe HT-1000-Y2K/HT-2000-Y2K is a smaller box containing one air switch that controls the pump and an electronic hi limit which is reset by the same button controlling the pump. The Micro-Topside control is substantially smaller and may only be used with the HT-1000-Y2K/HT-2000-Y2K controlsMust order pump cord separately 58-439-2625 931213-000

Heat Recovery Control SeriesThis series of controls is designed specifically for spas employing motor heat recovery jackets. The control includes a hi limit with remote, spaside reset, a 10-minute timer circuit for direct pump control, two momentary contact air switches for hi limit reset and timer control initiation, and three power cords for line, pump, and spaside control faceplate label designed of these controls incorporates READY, HEAT ON, and TEMP FAULT indicators which are illuminated to display equipment status 58-319-2530 CC2-120-06-I-07